Top of the page

Formfutura StoneFil Pottery Clay 2.85mm 2kg

Item No. 210000004776
StoneFil is a PLA-based filament which is based on the modified and easy-to-print EasyFil PLA compound and is gravimetrically filled with 50% of powdered stone. This high “stone filling” has resulted in a 3D printer filament with remarkable aesthetic features and a significant higher material densit
Suggested Retail Price €109.5
Retail discount 20%
Price €87.6
price per Piece
excl. tax
3 in stock
Loading
Piece

Description

StoneFil is a PLA-based filament which is based on the modified and easy-to-print EasyFil PLA compound and is gravimetrically filled with 50% of powdered stone.

This high “stone filling” has resulted in a 3D printer filament with remarkable aesthetic features and a significant higher material density up to 37% higher than “normal” PLA. StoneFil is an easy-to-print 3D printer filament and printed objects have an extremely matte stone-like finish.
Unique features
  • Easy to print
  • 50% gravimetric powdered stone filling
    • ±37% heavier than “normal” PLA
  • Matte and rough stone-like finish
General printing guidelines
Nozzle size: = 0.4mmLayer height: = 0.2mmFlow rate: ± 110%
Print temp: ± 215 - 230° CPrint speed: SlowRetraction: Yes ± 5mm
Heat bed: ± 0 - 60° CFan speed: 50-100%Experience level: Beginner
Abrasiveness
StoneFil has a very high filling with stone powders and therefore the filament can have a slightly more abrasive effect on brass nozzles than unfilled filaments.
Filament length
?: 1.70 g/cc50 gr coil0.5 Kg spool


Ø 1.75mm± 12.2m± 122m


Ø 2.85mm± 4.6m± 46m


Nozzle cleaning
When printing with filled/composite filaments it is recommended to clean your nozzle immediately after printing by feeding 15-20cm PLA filament through your nozzle. This will make sure that any potential fillers are flown out of your nozzle. It is even better to use glow in the dark PLA as the extremely hard phosphorous particles are much more likely to scrape out residual waste from your nozzle.

Product export information
HS Code: 39169090Description: MonofilamentCountry of origin: the Netherlands
Compliance
This filament is compliant to below listed directives and regulations.
  • RoHS directive 2011/65/EC
  • REACH directive 1907/2006/EC
  • Specifications

    Brand
    Formfutura
    GTIN
    8720629062211
    Article no. manufacturer
    STNF-285PCLY-02000
    Density
    0 g/cc
    Tensile strength
    0 MPa
    Tensile modulus
    0 MPa
    Elongation at break
    0 %
    Flexural strength
    0 MPa
    Flexural modules
    0 MPa
    Izod impact (notched)
    0 J/m

    Formfutura StoneFil Pottery Clay 2.85mm 2kg

    Item No. 210000004776
    StoneFil is a PLA-based filament which is based on the modified and easy-to-print EasyFil PLA compound and is gravimetrically filled with 50% of powdered stone. This high “stone filling” has resulted in a 3D printer filament with remarkable aesthetic features and a significant higher material densit
    Suggested Retail Price €109.5
    Retail discount 20%
    Price €87.6
    price per Piece
    excl. tax
    3 in stock
    Loading
    Piece

    Description

    StoneFil is a PLA-based filament which is based on the modified and easy-to-print EasyFil PLA compound and is gravimetrically filled with 50% of powdered stone.

    This high “stone filling” has resulted in a 3D printer filament with remarkable aesthetic features and a significant higher material density up to 37% higher than “normal” PLA. StoneFil is an easy-to-print 3D printer filament and printed objects have an extremely matte stone-like finish.
    Unique features
    • Easy to print
    • 50% gravimetric powdered stone filling
      • ±37% heavier than “normal” PLA
    • Matte and rough stone-like finish
    General printing guidelines
    Nozzle size: = 0.4mmLayer height: = 0.2mmFlow rate: ± 110%
    Print temp: ± 215 - 230° CPrint speed: SlowRetraction: Yes ± 5mm
    Heat bed: ± 0 - 60° CFan speed: 50-100%Experience level: Beginner
    Abrasiveness
    StoneFil has a very high filling with stone powders and therefore the filament can have a slightly more abrasive effect on brass nozzles than unfilled filaments.
    Filament length
    ?: 1.70 g/cc50 gr coil0.5 Kg spool


    Ø 1.75mm± 12.2m± 122m


    Ø 2.85mm± 4.6m± 46m


    Nozzle cleaning
    When printing with filled/composite filaments it is recommended to clean your nozzle immediately after printing by feeding 15-20cm PLA filament through your nozzle. This will make sure that any potential fillers are flown out of your nozzle. It is even better to use glow in the dark PLA as the extremely hard phosphorous particles are much more likely to scrape out residual waste from your nozzle.

    Product export information
    HS Code: 39169090Description: MonofilamentCountry of origin: the Netherlands
    Compliance
    This filament is compliant to below listed directives and regulations.
  • RoHS directive 2011/65/EC
  • REACH directive 1907/2006/EC
  • Specifications

    Brand
    Formfutura
    GTIN
    8720629062211
    Article no. manufacturer
    STNF-285PCLY-02000
    Density
    0 g/cc
    Tensile strength
    0 MPa
    Tensile modulus
    0 MPa
    Elongation at break
    0 %
    Flexural strength
    0 MPa
    Flexural modules
    0 MPa
    Izod impact (notched)
    0 J/m